Membership questions? Log in issues? Email info@brewersassociation.org

Author Topic: I got a pump... now what?  (Read 4974 times)

Offline a10t2

  • Official Poobah of No Life. (I Got Ban Hammered by Drew)
  • *********
  • Posts: 4696
  • Ask me why I don't like Chico!
    • SeanTerrill.com
I got a pump... now what?
« on: January 18, 2010, 06:58:01 pm »
Just kidding, I've already brewed with my new March pump once and it was awesome. But I have a few questions:

1. I could use it to pump from the mash tun but I didn't because I was worried about either compacting the grain bed down so far it wouldn't drain, pulling bits of husk through, or both. Anyone have experience with this? I lauter through a slotted CPVC manifold FWIW.

2. When I started my whirlpool, using the pump to pull wort from the bottom of the kettle, through the CFC, and back in at the top, I had a lot of hop particles and break running through the system. By the time I was done it was running clear, but after all was said and done I started worrying. I don't think any of it is hard enough to actually do damage; I'm more worried about binding up the impeller and burning out the motor or something like that. Am I just obsessing?

3. Finally, I cleaned everything up by pumping hot Oxiclean through it, then running hot water through until it ran clear, then blowing through it to get as much water out as possible. Is there anything else I should be doing to clean it? I guess I could take the head off, but it seems like pretty soft plastic (I almost stripped one of the threads just putting the fittings on). Maybe I'll compromise and clean it every 3-4 brews. How well do the plastic heads hold up long-term?
Sent from my Microsoft Bob

Beer is like porn. You can buy it, but it's more fun to make your own.
Refractometer Calculator | Batch Sparging Calculator | Two Mile Brewing Co.

Offline skiwithg

  • 1st Kit
  • *
  • Posts: 8
Re: I got a pump... now what?
« Reply #1 on: January 19, 2010, 04:43:39 am »
I pump from the MLT (with a SS braid) to BK.  If you have a valve on the output of your pump, throttle that way back to avoid stuck sparge.  I usually give the mash a few stirs during the drain (batch sparging).

For cleaning, I just recirculate boiling or near-boiling water from my HLT for 10 minutes after use, but I don't use the pump to whirlpool, so less of a concern for me since my use is all hot-side.  I remove the head (with valves & QD still attached) each time.  One recommendation:  throw the screws that hold plastic head on in the trash immediately and get stainless replacements.

Cheers,
Glenn

Offline hopfenundmalz

  • Global Moderator
  • I must live here
  • *****
  • Posts: 10678
  • Milford, MI
Re: I got a pump... now what?
« Reply #2 on: January 19, 2010, 06:27:38 am »
The pump can be throttled on the out put, and the flow even shut off.

I use mine throttled back to transfer from the mash/lauter tun to the boil kettle.  Go slow.

For the boil, I sanitize by running the pump to recirc. as the wort is coming to boil.  Then I pump for the last 15 min. of the boil.

Cleaning is just a water flush of all the hoses, CFC and pump.


Jeff Rankert
AHA Lifetime Member
BJCP National
Ann Arbor Brewers Guild
Home-brewing, not just a hobby, it is a lifestyle!

Offline Thirsty_Monk

  • Brewmaster General
  • *******
  • Posts: 2514
  • Eau Claire WI
    • Lazy Monk Brewing
Re: I got a pump... now what?
« Reply #3 on: January 19, 2010, 12:52:56 pm »
1) as other said put a ball valve on OUT post and control flow that way.

2) Pallet hops are fine. They do not get stuck in propeller unlike whole hops.
If using whole hops use a hop bag.

3) After using just clean it with nice warm water (flush out all the sugars) till clean and that would be it.
No need to take the pump head off.
If you are not going to brew for some time blowing water off is fine (less possibility to grow molds).
I make a loop with hose from in post to out post when I store my pump.
« Last Edit: January 19, 2010, 12:54:58 pm by Thirsty_Monk »
Na Zdravie

Lazy Monk Brewing
http://www.lazymonkbrewing.com

Offline a10t2

  • Official Poobah of No Life. (I Got Ban Hammered by Drew)
  • *********
  • Posts: 4696
  • Ask me why I don't like Chico!
    • SeanTerrill.com
Re: I got a pump... now what?
« Reply #4 on: January 19, 2010, 10:24:07 pm »
I do have a ball valve on it, so I'll throttle it back and try pumping from the tun next time. (Good to know it can be shut off that way too; I was doing a good impersonation of a chicken with its head cut off, running to and from the switch last time.) I'm pretty OCD about cleaning, so I'll probably end up taking the head off eventually, just to make sure nothing is growing. Per Glenn's suggestion, I'll be sure to replace the screws when I do.

Thanks for the help, guys.
Sent from my Microsoft Bob

Beer is like porn. You can buy it, but it's more fun to make your own.
Refractometer Calculator | Batch Sparging Calculator | Two Mile Brewing Co.

Offline nyakavt

  • Assistant Brewer
  • ***
  • Posts: 108
Re: I got a pump... now what?
« Reply #5 on: January 20, 2010, 08:50:30 am »
I took the head off of mine after about 6 months of use, it was clean as a whistle.  I do recirc oxyclean or water for about 20 min after I stop the whirlpool, so I think as long as the head doesn't stay full of wort you'll be fine.

Offline blatz

  • Official Poobah of No Life. (I Got Ban Hammered by Drew)
  • *********
  • Posts: 3513
  • Paul Blatz - Jupiter, FL
Re: I got a pump... now what?
« Reply #6 on: January 20, 2010, 09:20:56 am »
I took the head off of mine after about 6 months of use, it was clean as a whistle.  I do recirc oxyclean or water for about 20 min after I stop

+1 - 2 years running now and not a problem.

Don't forget to oil the pump every 4-6months though  ;)
The happiest people don’t necessarily have the best of everything; they just make the best of everything they have.

BJCP National: F0281

Offline Thirsty_Monk

  • Brewmaster General
  • *******
  • Posts: 2514
  • Eau Claire WI
    • Lazy Monk Brewing
Re: I got a pump... now what?
« Reply #7 on: January 20, 2010, 11:37:51 am »
I took the head off of mine after about 6 months of use, it was clean as a whistle.  I do recirc oxyclean or water for about 20 min after I stop

+1 - 2 years running now and not a problem.

Don't forget to oil the pump every 4-6months though  ;)
I heard about oiling the pump but it is not obvious where. (May be I just did not spent enough time on it)
Na Zdravie

Lazy Monk Brewing
http://www.lazymonkbrewing.com

Offline a10t2

  • Official Poobah of No Life. (I Got Ban Hammered by Drew)
  • *********
  • Posts: 4696
  • Ask me why I don't like Chico!
    • SeanTerrill.com
Re: I got a pump... now what?
« Reply #8 on: January 20, 2010, 11:49:09 am »
I heard about oiling the pump but it is not obvious where. (May be I just did not spent enough time on it)

There's a label on top that says "OIL" with arrows pointing to a hole on either end.
Sent from my Microsoft Bob

Beer is like porn. You can buy it, but it's more fun to make your own.
Refractometer Calculator | Batch Sparging Calculator | Two Mile Brewing Co.

Offline Thirsty_Monk

  • Brewmaster General
  • *******
  • Posts: 2514
  • Eau Claire WI
    • Lazy Monk Brewing
Re: I got a pump... now what?
« Reply #9 on: January 20, 2010, 01:10:51 pm »
I heard about oiling the pump but it is not obvious where. (May be I just did not spent enough time on it)

There's a label on top that says "OIL" with arrows pointing to a hole on either end.

you made me go into the basement and look. And guess what it is right on label.
Thank you
Na Zdravie

Lazy Monk Brewing
http://www.lazymonkbrewing.com

Offline scruz

  • 1st Kit
  • *
  • Posts: 1
Re: I got a pump... now what?
« Reply #10 on: January 22, 2010, 12:43:27 pm »
what kind of oil?  mineral?

Offline denny

  • Administrator
  • Retired with too much time on my hands
  • *****
  • Posts: 27093
  • Noti OR [1991.4, 287.6deg] AR
    • Dennybrew
Re: I got a pump... now what?
« Reply #11 on: January 22, 2010, 12:51:37 pm »
3 in 1 is what I've used and heard of others using.
Life begins at 60.....1.060, that is!

www.dennybrew.com

The best, sharpest, funniest, weirdest and most knowledgable minds in home brewing contribute on the AHA forum. - Alewyfe

"The whole problem with the world is that fools and fanatics are always so certain of themselves, and wiser people so full of doubts." - Bertrand Russell

Offline Thirsty_Monk

  • Brewmaster General
  • *******
  • Posts: 2514
  • Eau Claire WI
    • Lazy Monk Brewing
Re: I got a pump... now what?
« Reply #12 on: January 22, 2010, 01:52:19 pm »
what kind of oil?  mineral?
It is on pump label.
Do you want me to go to the basement AGAIN!!!
Na Zdravie

Lazy Monk Brewing
http://www.lazymonkbrewing.com

Offline dontblake

  • Conference
  • Assistant Brewer
  • *****
  • Posts: 103
    • Indian Peaks Alers
Re: I got a pump... now what?
« Reply #13 on: January 22, 2010, 05:11:09 pm »
Yes, 3-in-1 oil.
One handy thing that I did is attached a 50' extension cord to the pump (cut one end and wired it directly to the pump).   About 6' from the pump, I installed a switch (regular lightswitch in a standard metal box ).   Makes it real handy if an outlet isn't nearby (a godsend at last year's big brew day), and having the switch far enough away from the pump keeps it from getting wet.
All this might change, however, when/if I ever get around to making a brew stand.

another thing that someone mentioned to me last year...   Install your pump below your tun/kettle and then put a T in place at the output of the ball valve at your pump output.  In this T, install another valve - this you can use to prime the pump by simply opening that 'relief' valve.   Hope that made sense.

Cheers
Don Blake, Erie CO
Founder, Indian Peaks Alers
Grand Master BJCP Judge

Offline rep

  • Cellarman
  • **
  • Posts: 72
Re: I got a pump... now what?
« Reply #14 on: January 24, 2010, 04:18:18 pm »
Yes, 3-in-1 oil.
One handy thing that I did is attached a 50' extension cord to the pump (cut one end and wired it directly to the pump).   About 6' from the pump, I installed a switch (regular lightswitch in a standard metal box ).   Makes it real handy if an outlet isn't nearby (a godsend at last year's big brew day), and having the switch far enough away from the pump keeps it from getting wet.
All this might change, however, when/if I ever get around to making a brew stand.

another thing that someone mentioned to me last year...   Install your pump below your tun/kettle and then put a T in place at the output of the ball valve at your pump output.  In this T, install another valve - this you can use to prime the pump by simply opening that 'relief' valve.   Hope that made sense.

Cheers

By chance anybody have pictures of this type of set up?
Wear Wool, Sit on Leather, Ride Lugged Steel