Author Topic: Bottle Fill Line  (Read 1115 times)

Online theDarkSide

  • Brewmaster General
  • *******
  • Posts: 2174
  • Derry, NH
    • View Profile
Bottle Fill Line
« on: February 28, 2013, 07:37:26 AM »
So here's one that bugs me.  In several competitions, most scoresheets have had the low fill or high fill line checked.  I know you're not supposed to get points off for that, but is this picture ( taken from the internet ) a good indication of a proper fill.


I use a beergun and it is said that if you fill it to the top, the displacement of the gun will result in a proper fill when removed, but I'm not too sure of that so I'll hit it with a little extra.

Thanks.
Sergeant - BNArmy Member
AHA Member
Seacoast Homebrew Club Member
https://www.facebook.com/SeacoastHomebrewClub
Stephen M.
------------------------------------------------

Online mtnrockhopper

  • Official Poobah of No Life.
  • *
  • Posts: 3113
  • Delaware
    • View Profile
Re: Bottle Fill Line
« Reply #1 on: February 28, 2013, 08:08:43 AM »
Looks good to me - are you aiming for higher when you top off? I fill to the top and remove with my bottling wand and that gives very consistent fills, but I don't know how similar the tube diameter is compared to a beer gun.
 
I once got a scoresheet comment "Nice fill!" - I don't really know how the fill level can be THAT good either.
Jimmy K

Delmarva United Homebrewers - President by inverse coup when the old president ousted himself.
AHA Member since 2006
BJCP: B0958

Offline AmandaK

  • Senior Brewmaster
  • ******
  • Posts: 1029
  • Redbird Brewhouse
    • View Profile
Re: Bottle Fill Line
« Reply #2 on: February 28, 2013, 08:55:48 AM »
I've noticed that when I cap on foam, my fill line varies a bit.

Regardless, the only thing I've ever noted about the fill line on comp entries was, "Generous fill, thanks for the extra beer! :)"
Amanda Kertz
Kansas City Bier Meister
BJCP National

Redbird Brewhouse - Current Project: Full Basement Bar Build

Offline GolfBum

  • Cellarman
  • **
  • Posts: 92
  • Lakewood, CO
    • View Profile
Re: Bottle Fill Line
« Reply #3 on: February 28, 2013, 01:48:28 PM »
That picture looks good to me. That's where I like to fill my bottles to. Once the beer gets to the top of the bottle take out the wand and you should be perfect.

I was stewarding a competition once and every bottle I saw was low except for one, which was filled all the way to the top. I don't know how you do that but it was funny for the judges to see me soaked in beer.

Offline Joe Sr.

  • Brewmaster General
  • *******
  • Posts: 2488
  • Chicago - NORTH SIDE
    • View Profile
Re: Bottle Fill Line
« Reply #4 on: February 28, 2013, 02:03:42 PM »
I've noticed that when I cap on foam, my fill line varies a bit.

I've experienced the same thing.  I wind up losing some beer in an effort to get an even fill line sometimes. 

Not really a problem, except when the beer foams too much if the bottles are warm or the bottling pressure to high.  I started filling the bottles in a tupperware tub so I can pour off the extra into my glass.  Gross, perhaps, but waste not want not.  Or something.
It's all in the reflexes. - Jack Burton

Offline tom

  • Senior Brewmaster
  • ******
  • Posts: 1110
  • Denver, CO
    • View Profile
Re: Bottle Fill Line
« Reply #5 on: March 02, 2013, 09:14:15 AM »
Actually, for filling bottles from a keg, I prefer a high fill.

And no worries, no points are affected.
Brew on