Author Topic: How to keep the ball valve on a boiling kettle from clogging  (Read 889 times)

Offline guido

  • Assistant Brewer
  • ***
  • Posts: 219
    • View Profile
Normally, I put a false bottom in my 10 gallon Polarware kettle to keep to the whole hops from clogging the ball valve when I make my APA's and IPA's.  This time, however, I need to make a bigger batch.  I have a 20 gallon Polarware kettle, but no false bottom.  I have a 45 degree copper pipe elbow (pointed downward, of course) that's threaded into the inside of the kettle.  Is there a simple, low-tech way to keep the whole hops from clogging the ball valve?  Yeah...I could bag everything, but I like the hops to be more "exposed" to the wort.
Well...I woke up this morning and I got myself a beer

     -"Roadhouse Blues,"  Jim Morrison

Offline Pinski

  • Senior Brewmaster
  • ******
  • Posts: 1556
  • Portland, Oregon
    • View Profile
Re: How to keep the ball valve on a boiling kettle from clogging
« Reply #1 on: June 20, 2013, 12:41:01 PM »
I prefer free range whole hops as well yet if I were you, I'd just go with hop socks. I've used them many times with fantastic results. You could also make an el cheapo "hop spider" by putting a dowel over the boil kettle and suspending a large mesh bag from the dowel by the drawstrings, keeping the opening above the surface of the wort.  Either way, I doubt your beer will suffer. Especially if you bump the quantities just a tad.
Thank you BEER!

Offline guido

  • Assistant Brewer
  • ***
  • Posts: 219
    • View Profile
Re: How to keep the ball valve on a boiling kettle from clogging
« Reply #2 on: June 20, 2013, 12:57:12 PM »
I prefer free range whole hops as well yet if I were you, I'd just go with hop socks. I've used them many times with fantastic results. You could also make an el cheapo "hop spider" by putting a dowel over the boil kettle and suspending a large mesh bag from the dowel by the drawstrings, keeping the opening above the surface of the wort.  Either way, I doubt your beer will suffer. Especially if you bump the quantities just a tad.

The hop spider sounds like an excellent idea!
Well...I woke up this morning and I got myself a beer

     -"Roadhouse Blues,"  Jim Morrison

Offline tygo

  • I spend way too much time on the AHA forum
  • ********
  • Posts: 2622
  • Sterling, VA
    • View Profile
Re: How to keep the ball valve on a boiling kettle from clogging
« Reply #3 on: June 20, 2013, 03:59:59 PM »
When I use my kettle with the pickup tube and whole hops I put a little section of bazooka screen on the end of the tube and crimp it down.  Worked perfectly for whole hops.  I cut off the last 3 inches of a spare bazooka I had lying around from a previous project to make it.
Clint
Wort Hogs

Fermenting: Wit
On Tap: Lucifer's Hammer Golden Strong Ale, Dopplebock, Old Fuzzynut's Ale

Offline tonyp

  • Brewmaster
  • *****
  • Posts: 563
  • If it ain't broke you aren't trying hard enough...
    • View Profile
Re: How to keep the ball valve on a boiling kettle from clogging
« Reply #4 on: June 21, 2013, 12:12:06 AM »
Another low tech idea that might work is just taking one of those stainless steel kitchen scrubies and jamming it over the intake.

Something like this:



I haven't tried it myself since I have a horizontal connector with a bazooka screen, but it just might be crazy enough to work.
Live from the Jersey Shore!

Bottled:
Grandpa Louie's Cream Ale
Eagle Point Pale Ale


Phrases for Creatives, #22:
"I'll try being nicer if you'll try being smarter."

Offline guido

  • Assistant Brewer
  • ***
  • Posts: 219
    • View Profile
Re: How to keep the ball valve on a boiling kettle from clogging
« Reply #5 on: June 21, 2013, 02:09:12 AM »
These have all been good solutions.
Well...I woke up this morning and I got myself a beer

     -"Roadhouse Blues,"  Jim Morrison

Offline guido

  • Assistant Brewer
  • ***
  • Posts: 219
    • View Profile
Re: How to keep the ball valve on a boiling kettle from clogging
« Reply #6 on: June 22, 2013, 05:04:23 PM »
I prefer free range whole hops as well yet if I were you, I'd just go with hop socks. I've used them many times with fantastic results. You could also make an el cheapo "hop spider" by putting a dowel over the boil kettle and suspending a large mesh bag from the dowel by the drawstrings, keeping the opening above the surface of the wort.  Either way, I doubt your beer will suffer. Especially if you bump the quantities just a tad.

The hop spider looks great.  It'll have its maiden voyage tomorrow.
Well...I woke up this morning and I got myself a beer

     -"Roadhouse Blues,"  Jim Morrison