Membership questions? Log in issues? Email info@brewersassociation.org

Author Topic: Stuck mash using new pump to recirc??  (Read 4843 times)

Offline chuckger

  • 1st Kit
  • *
  • Posts: 2
Stuck mash using new pump to recirc??
« on: May 04, 2010, 03:17:56 pm »
I just installed a March 809 hot pump on my system and was excited to use it for circulating the mash before starting to drain into the boil kettle.  I ran the pump full open right off the bat and it worked great at clearing up the runnings, but the amont of wort being pumped back into the kettle quickly became less and less.  Then when I ran from mash to boil, it ran super slow with or without the pump, it almost seems to me that the pump sucked the grain into my false bottom and cause it to clog, any body had anything like this happen to them while using a pump?  This was my first stuck mash EVER!  and I didn't like it much. 

Offline denny

  • Administrator
  • Retired with too much time on my hands
  • *****
  • Posts: 27070
  • Noti OR [1991.4, 287.6deg] AR
    • Dennybrew
Re: Stuck mash using new pump to recirc??
« Reply #1 on: May 04, 2010, 03:54:50 pm »
I'd guess full open was the problem.  You probably compacted your grain bed.
Life begins at 60.....1.060, that is!

www.dennybrew.com

The best, sharpest, funniest, weirdest and most knowledgable minds in home brewing contribute on the AHA forum. - Alewyfe

"The whole problem with the world is that fools and fanatics are always so certain of themselves, and wiser people so full of doubts." - Bertrand Russell

Offline tom

  • Senior Brewmaster
  • ******
  • Posts: 1109
  • Denver, CO
Re: Stuck mash using new pump to recirc??
« Reply #2 on: May 04, 2010, 08:47:10 pm »
Definitely. I go 50% open at the most.
Brew on

Offline hopfenundmalz

  • Global Moderator
  • I must live here
  • *****
  • Posts: 10675
  • Milford, MI
Re: Stuck mash using new pump to recirc??
« Reply #3 on: May 05, 2010, 05:58:10 am »
Put a ball valve on the pump's output to control the flow.  Otherwise the vacuum you create will pull the grainbed down and cause it to stick when you are sparging.

When recirculating the mash for temperature steps with direct fire and the pump running on a higher flow, I give the mash a stir now and then to keep it suspended.

Experiece will show you what to do, and now I don't even think about it while brewing.
Jeff Rankert
AHA Lifetime Member
BJCP National
Ann Arbor Brewers Guild
Home-brewing, not just a hobby, it is a lifestyle!

Offline chuckger

  • 1st Kit
  • *
  • Posts: 2
Re: Stuck mash using new pump to recirc??
« Reply #4 on: May 05, 2010, 12:31:32 pm »
I figured that was the problem, running full open I mean, I have not had a chance to brew again so I have not tried it again but next time I will definately run about 30% or so instead of 100% just wanted some one elses insight.  Thanks guys.

Offline a10t2

  • Official Poobah of No Life. (I Got Ban Hammered by Drew)
  • *********
  • Posts: 4696
  • Ask me why I don't like Chico!
    • SeanTerrill.com
Re: Stuck mash using new pump to recirc??
« Reply #5 on: May 05, 2010, 03:29:02 pm »
I had the same problem. The biggest reason I've stuck with malt conditioning is that it lets me run the pump full open without a stuck sparge. Each runoff takes less than two minutes.
Sent from my Microsoft Bob

Beer is like porn. You can buy it, but it's more fun to make your own.
Refractometer Calculator | Batch Sparging Calculator | Two Mile Brewing Co.

Offline bobby_m

  • Cellarman
  • **
  • Posts: 35
    • BrewHardware
Re: Stuck mash using new pump to recirc??
« Reply #6 on: June 05, 2010, 02:23:57 pm »
Start the recirculation really slow to set the bed without compacting, then run no more than 50% throttle. I also agree that conditioning your malt before the crush is a real help there... assuming you own a mill.

Bobby

Offline richardt

  • Senior Brewmaster
  • ******
  • Posts: 1227
Re: Stuck mash using new pump to recirc??
« Reply #7 on: June 10, 2010, 07:15:12 am »
... biggest reason I've stuck with malt conditioning is that it lets me run the pump full open without a stuck sparge. Each runoff takes less than two minutes.

Improved lauterability was the reason I gave malt conditioning a try.  Problem was that I tried to "eyeball" the wetness of the grains rather than do the math--ended up using 3 times the amount of water I should have and with rollers that looked like corndogs.  Not to mention a lot of unnecessary aggravation taking the BC apart, cleaning it, and putting it back together.  Don't overdo the hydration of the grains.  Stay on the drier side.

Offline wilypig

  • Cellarman
  • **
  • Posts: 94
Re: Stuck mash using new pump to recirc??
« Reply #8 on: June 14, 2010, 11:21:06 am »
I recently started using a Barley Crusher instead of my Corona mill and had just read the 2 articles in the BYO and Zymurgy on Malt conditioning. I just throw about 0.5 cup of hot water in my base grain and stir with my hand until well combined and rest for 5 to 10 minutes. After grinding I run my specialty malts and crystal through with out conditioning and that cleans the rollers very nicely.
If you can make mac and cheese from a box, you can make great beer.
Weiz Guys Homebrew club Loveland CO
Wilypig Fermentation Specialties