[brew-witch]

OK, so I'm seeing anywhere from 5 - 20+ different brews going at the same time... and many of you seem to do larger batches (that is, larger than the typical 5 gal)... so my questions are:

1. Where do you find the time to do all this? 

2. Where do you keep everything (fermenters, kegs, bottles, massive amounts of equipment)? 

I am starting very small for a number of reasons, but space is the biggest reason.  And time!  I'd rather spend more time (what little of it I have to spare) making a lot of different small batches (3 gal or less even) for more variety (my tastebuds get bored easily) than having 5, 10, or more gallons of the same beer that would take me forever to drink, or even trade with others.  So that leads me to question #3:

3. I want to hear all the pros and cons of making smaller batches (preferably more pros than cons  )

Thanks!

[a10t2]

2: Until a year ago, I lived in an apartment, and all of my beer equipment had to fit in a closet, plus the kegerator. Bucket fermenters stack, boil kettles nest and sit on top of the propane burner with the chiller inside, miscellaneous equipment inside the mash tun. It was actually the coat closet, and the beer equipment only took up the space from the floor to the bottom of the actual coats.

3: There are only two cons to small batches, IMHO: the extra time commitment per beer, and the fact that not having a keg filled just seems like a waste of space to me. Other than that, you get more experience, more variety, etc.

[hopfenundmalz]

I have a lot of beers going at one time.

Answers:

1.  I am now retired.  My hobby is a good use of my time.

2. Garage and a room(s) in the basement.

3. Small batches:
Pros - You can experiment with many recipies.   Less mass, can move it easy.  Can't think of much else
Cans - About the same amount of time and effort to make a 10 gallon batch, so the yeild is low.

[rabid_dingo]

Parenthood slowed my production. I went from having 60 gallons of beer stocked for the summer and fall to, well, 10...

1.I shoot for weekends. Even if it is 1-2 weekends a month. Plus, I was furloughed from full time to part time 1.5 years
ago. I pick up the hours I need around my work week and avoid at least one day off, for family or what not. But I manage.
Lately I have enjoyed the early hours. I can get up 3-5 hour earlier that what I am used to and there is sunlight. (some will laugh but getting up at 4:45-6:30am is not normal for me and I see the advantage of having my daily morning routine done with at 9:00am.

2. I have 22-23 ball lock kegs. Once kegged they sit right outside the keggerator to the right. I have to
admit I cannot park a car in my two-car garage...  I am horrible of keeping a timely schedule with primary and
after. Some beers cross the 4-6 week line in primary. I have never worried and they are all fine. They go right to keg.

3. I figure that I don't bottle much anymore and I have yet to get the 2.5 or 3 gallon kegs so might as well
go for the 5 or 10 gallon batch. My last one was the imperial porter 10 gallon batch and It took an extra
3 hours but only because of the additional time it took to heat strike water and heat to boiling once
the wort was collected (I was at the very limit of my max volume for mash tun and boil kettle) Normal 10
gallon batches are only an hour difference for me.

Pros- conducive to small breweries' needs.
Cons- limited supply, even if there is a lot of variety. You still run out faster of each batch.

[dean]

I have to agree with a10t2, you can adapt quicker with small batches so you gain experience faster.   Three gallon batches would be good, if you like beer anything smaller might tick you off if you make  a really good batch when its gone, but you can have another batch conditioning behind it.  

I guess it really doesn't matter what volume you brew, the problem seems to be storing what you have brewed.  If you make a good batch and don't have a replacement ready then you're still going to have to wait for the next batch to finish which means you're going to wait for nature to fulfill its destiny and that will be at its own pace.  Too many people want to rush the process, I've done it and sometimes I still do it.  If I didn't procrastinate so much I'd have plenty of beer on hand at all times and there is always someplace to tuck a keg away or case(s) of bottled beer.

Brew with what you have available, brew as often as you can and feel like it.  Yeh, it takes time but you do have time if you plan it and stick to your plan, understand that it won't brew itself and that it takes just as much time to brew 3 gallons as it takes to brew 5 gallons, even 10+ gallons takes nearly the same amount of time.  LME is quicker to start with but it also costs more per batch "initially".  Cost can be prohibitive as much as time or space.  But with LME you don't have as much equipment involved and each batch is more likely to be a success until you become more experienced doing AG.  We say AG gives you more control and that is true, but it is easier to mess up a batch... being the control freaks we are and so we have to own up to those bad batches.  

Just Do It... one or the other... damn the torpedos, full speed ahead!  

[majorvices]

Let me start this by saying that right now I have a 1 bbl brewery on my back porch and a 42 gallon conical fermenter in my garage that is controlled by an upright freezer. This equipment is only 1/4 mine though.

I also have 2 other 14 cu ft deep chest freezers in my garage, one for fermenting and one for lagering. Plus another 14 cu ft chest freezer in my pub room for serving. My homebrew set up is a 12 gallon system.

As far as where I keep it all, I have to admit, it is all over the damn place but most of it does get crammed into a junk room when not in use.

As far as the time goes, I don't know what to tell you. I find it easy to brew a batch on the weekend and I can pretty much brew around whatever I am doing (cut the grass, throw ball with the kids, even go out for a 6 mile run.) There are lots of down times in the brewing process. A 6 hour brew day (I brew all grain) really only has about 2 hours of solid work.

Brewing is far from my only gig, too. I also am an avid back packer and hiker. I run 30 miles or so a week. Plus I have 2 kids, 2 dogs and a 7 acre piece of property to maintain. Plus I ride motorcycles, lift weights, dabble in martial arts from time to time.

I also watch absolutely 0 hours of TV during the week so I get a lot of stuff done.

[dean]

I also watch absolutely 0 hours of TV during the week so I get a lot of stuff done.

+1, TV is a huge drain on anything and everything... yet I still watch certain shows and the news.  Lately I've been building a deck and I'm eyeballing it as a nice place to brew outside too.  SWMBO says no though because I've got a brewshed for that now.   

[4swan]

3. cons: santiation takes just as long for a 3 gallon batch versus 5 gallons.
pro: experiment with recipes (as stated earlier),  more variety available for guests, don't need to bother with starters, don't need as much space,  easier to clean up if you have a small kitchen (I often bonk the cabinets when cleaning my ten gallon pot.)

[dean]

Thinking about it more, I'm not sure batches smaller than 5 gallons actually give you more experience.  If brew-witch doesn't spend the time brewing for whatever reasons brew-witch might have then she isn't going to gain anything more.  If time and space for equipment are her issues then she should brew standard 5 gallon batches using Liquid Malt Extract.  She would save the expense of a mashtun, some tubing, possibly a grain mill, another burner or heating element, less gas or electricity and HLT (some people use their BK for dual purpose HLT/BK).  Most yeasts sold are pitchable for moderate gravities so she wouldn't have to split her yeast down and worry about how to save the remaining yeast and keeping it from becoming contaminated between brews.  I think in her case maybe she should stick with 5 gallon batches and use LME having little outlay for equipment expenses and space required for the extra equipment which would outweigh the cost of LME... in her case mind you.  Jmo... 

[theDarkSide]

1.  My wife does scrapbooking and will go to these all day sessions, so I have some leverage when I say I want to brew.  I typically brew only on weekends and try to start as early as possible so I can have a big chunk of the day to do all the other stuff.  I try to do as much as I can the night before ( crushing grain, getting water setup ) so it takes less time on brew day.  I do all grain and it takes about 5 hours from flame on to clean up.  I want to try a night time brew session one of these days, like Friday after work.  I just gotta watch the consumption during that time ( I don't usually drink during my morning brew sessions ).

2.  All my equipment is in my basement.  I have a walkout so it's eay to move stuff right outside from the basement door.  My wife gets the dining room for her scrapbooking and I get the basement, but at least I get to decorate the way I want.

3.  Making smaller batches will give you the ability to fine tune a recipe.  Also, some styles don't hang around long so the faster the are drank, the better.  On the flip side, some styles get better with aging, so if you are going to put all that time into aging a beer, it would be nice to have the bigger batch.

[brew-witch]

Thanks dean (and everyone) for the input.

I do understand that it takes just as long to brew 10 gal as 3... I'm just amazed at how much you all have going at the same time, lol!  Time is an issue as I work 6 days a week, but I have a lot of odd time available most days that can be used, and my weekends are usually filled with kayaking and/or hiking (+1 on the no tv, majorvices... except of course during hockey season... and baseball if i'm home to watch the games... work schedule always seems to correspond with ball games  )

Space will continue to be an issue as I have a big kitchen but I'm also an herbalist and have about 50 mason jars of dried herbs and that equipment in the pantry along with cases of beer bottles. And I have a basement, but share that space with the neighbors.. and soon some of my space will be taken up by a new 14' kayak.

So, I guess I'm looking for some support in doing my little 3-5 gal batches and keeping maybe just 2 or 3 going at any given time (so there is always variety as well as a steady supply).  Maybe when I can afford a kegging setup, I might increase production since (I'm guessing?) kegs won't take up as much space (or time) as bottles.  Though some bottles are nice for trading with other brewing friends. 

And yes, my plan for now is to stick with LME and just do some experimenting with that.  That's a big pull for me - experimenting and variety, and while I know I could hit something awesome and only have a small batch of it, I could just as well have a disaster and not have 10gal of it to dump.  My rationalization around this is that if I take good enough notes (which I am very Type-A about) I can probably come pretty close to re-creating that great batch if I wanted.

So thanks again all!  I will continue with my small batches and hope that I won't get laughed at by the big boys with their big toys 

[dean]

Hey, no problem, we all like telling other people how to or what to do.     Sometimes when I've screwed up a batch, I wish I'd stuck with LME... but then I get over it and make another batch.    

Good luck, keep us posted on your venture.   

[tygo]

1.  My wife does scrapbooking and will go to these all day sessions, so I have some leverage when I say I want to brew.  I typically brew only on weekends and try to start as early as possible so I can have a big chunk of the day to do all the other stuff.  I try to do as much as I can the night before ( crushing grain, getting water setup ) so it takes less time on brew day.  I do all grain and it takes about 5 hours from flame on to clean up.  I want to try a night time brew session one of these days, like Friday after work.  I just gotta watch the consumption during that time ( I don't usually drink during my morning brew sessions ).

This is pretty much how I work it except that I need to get my wife a hobby like that 

I often do night sessions and it's a nice compromise if somewhat tiring and there is the issue of consumption monitoring so you don't end up forgetting to put the hops in or pitch the yeast.  I usually try to get the strike water going right after dinner while doing kitchen clean up.  Then mash in before it's time for the kid's bath.  By the time bath time and bedtime are done I'm ready to start the runoff so it works out pretty well that way and I can usually finish up by 11:00 or so.  The times I've waited to start the brew session until later it was pretty rough.

[Slowbrew]

The nice thing about this hobby (or any hobby, really) is how and what you brew is up to you.  If it works for you, then it's perfect.

In my case, I usually brew 2 beers on a brew day.  Many times I will take day off work on Friday while no one else is home.  If I need to fit a session in on a Saturday, I have been know to get rolling at 3:00 AM so I'm done by 9:00.  Then it's off to softball, basketball, marching band or whatever, depending on the time of year.  My 4 kids keep me hopping.

I have 14 kegs (9 - 12 in some state of "full" at any given time) that I store in a custom built cabinet in my basement word working shop/store room for all the crap that won't fit anywhere else.  8^)  Out of 8 sets of Gorilla shelving units I get about one unit for beer stuff.

We added a room w/basement to our house a few years back so gained a ton of space for a cleanup area, storage, shop and kegerator so I'm pretty lucky.

Good luck with you brewing and do what works for you.

Paul

[richardt]

I recently jumped up to All-Grain 10 gallon batches outside on the Banjo burner (from partial grain/extract 5 gallon batches on the stove top).  While waiting for my AG equipment to come together--I researched my local water profile (and figured out why it is horrible for most of the beers I want to brew).  Both significantly improved the quality of the beers I make (i.e., going AG and using better water).

With regards to equipment, among the best advice I got was "get a bigger kettle that can handle a 10 gallon batch" (15 gallon is OK, but 20 gallon is preferable).  Sometimes the BrewSmith recipe calls for 15.5 or 16 gallons of pre-boil wort... so, with a 20 gallon kettle, I don't have boilover problems (less mess, and less worry).

Like you, my time is precious (family and kids in all the sports), so I take advantage of the 10 gallon batch size.  I often split up the batches.  I may do 5 gallons with one type of yeast and 5 gallons with another type of yeast.  Or, in the secondary, I may split them again and do 2.5 gallons with spices and 2.5 gallons w/o spices.  The result is 2 or 4 different beers within a similar style out of one brew day. 

It's not quite the same thing as "partigyle" where one takes the first runnings and makes a strong beer from it (high OG) and uses the second (and subsequent) runnings to make other beers (with lower OG's).  Although doing it that way gives you more beer styles with one brew day.