Author Topic: Solid bottom brew pots??  (Read 313 times)

Offline fahrphrompuken

  • 1st Kit
  • *
  • Posts: 5
Solid bottom brew pots??
« on: June 14, 2019, 02:33:32 PM »
Looking for a source for SS brewing vessels around 20 - 25 gal that do not have tri-clad bottoms. I am working on building a new system that utilizes electric heating elements and I want to weld tri-clamp fittings to the bottom of the pots, so I am pretty sure that the bottoms will need to be solid.

Offline ynotbrusum

  • Official Poobah of No Life.
  • *
  • Posts: 3219
Re: Solid bottom brew pots??
« Reply #1 on: June 14, 2019, 06:12:24 PM »
Polar ware and bayou classic offer single layer bottom on some of their kettles, IIRC.  Good luck with the welding - Brew Hardware has helpful you tube videos on the subject!
Hodge Garage Brewing: "Brew with a glad heart!"

Offline Robert

  • Official Poobah of No Life.
  • *
  • Posts: 3836
Re: Solid bottom brew pots??
« Reply #2 on: June 14, 2019, 10:20:10 PM »
The Polarware, Bayou and their ilk are a little lightweight for my taste.  Try searching restaurant supplies for something a bit sturdier.   My local restaurant supply house carries both tri clad and solid bottom SS stock pots, though I don't believe I've seen them there in those sizes.  But they certainly must exist.  Good luck.
Rob Stein
Akron, Ohio

I'd rather have questions I can't answer than answers I can't question.

Offline Thirsty_Monk

  • Brewmaster General
  • *******
  • Posts: 2397
  • Eau Claire WI
    • Lazy Monk Brewing
Solid bottom brew pots??
« Reply #3 on: June 14, 2019, 11:06:09 PM »
Looking for a source for SS brewing vessels around 20 - 25 gal that do not have tri-clad bottoms. I am working on building a new system that utilizes electric heating elements and I want to weld tri-clamp fittings to the bottom of the pots, so I am pretty sure that the bottoms will need to be solid.
I would advise against having heating elements straight up (if I read your post correctly)
Na Zdravie

Lazy Monk Brewing
http://www.lazymonkbrewing.com

Offline a10t2

  • Official Poobah of No Life.
  • *
  • Posts: 4597
  • Ask me why I don't like Chico!
    • SeanTerrill.com
Re: Solid bottom brew pots??
« Reply #4 on: June 15, 2019, 04:33:58 AM »
On the cost/benefit front, after about 30 batches in a 19 gal Brewmaster I'm still very happy with it. More than durable enough to drill out for fittings and comes with the basics already welded in. https://www.morebeer.com/category/brewmaster-kettles.html

Like Leos said, you'll give up some thermodynamic efficiency mounting the elements vertically.
Sent from my Microsoft Bob

Beer is like porn. You can buy it, but it's more fun to make your own.
Refractometer Calculator | Batch Sparging Calculator | Two Mile Brewing Co.

Offline mabrungard

  • Brewmaster General
  • *******
  • Posts: 2599
  • Water matters!
    • Bru'n Water
Re: Solid bottom brew pots??
« Reply #5 on: June 15, 2019, 01:46:28 PM »
Based on what I've seen, welding fittings into SST kettles is not really a great option. Using swaged fittings and silver soldering is easily accomplished at the homebrew level and is plenty strong and durable enough.
Martin B
Carmel, IN

BJCP National
Foam Blowers of Indiana (FBI)

Brewing Water Information at:
https://sites.google.com/site/brunwater/

Like Bru'n Water on Facebook
https://www.facebook.com/Brun-Water-464551136933908/?ref=bookmarks

Offline fahrphrompuken

  • 1st Kit
  • *
  • Posts: 5
Re: Solid bottom brew pots??
« Reply #6 on: June 17, 2019, 04:41:31 PM »
Thanks for the ideas and comments!

I have looked at the Bayou, and Polaraware stuff and agree they seem too thin to get a good weld that will be structurally sound. Have also seen bad reviews that complain about inconsistent wall thickness, un-passivated surfaces that start rusting, etc.

Still looking at restaurant supply sources, but there is a substantial difference in cost for the thicker solid bottom pots, as I was expecting, but it's quite a steep curve to say the least. I will probably stick with keggles for the time being, at least they weld up fairly easy. Luckily I have been a "hobby" welder for several years and have a decent tig machine that I have used for SS (304/316/409).

I have tried the silver soldering method as well with great results. It's an excellent way to go if you don't have access to adequate equipment, and experience in welding.


My plan for the electric heating elements for the boil kettle are to make them vertical, but contained in a calandria sort of setup. That will allow the concentrated heat inside the cylinder to pull wort from the bottom through open ports and with convection push it up to open ports on the top of the cylinder (sort of like a percolator). There will be three elements controlled by the PLC that will each have it's own PID loop, so as the demand decreases (as it gets closer to boiling) it will shut off one or two elements as necessary to keep just enough heat for a good rolling boil. Of course this is all R&D at this point and have no idea how the end result will pan out, or what the final configuration will be. But heck, half the fun is trying new ideas and spending countless hours tinkering with it.