Author Topic: Advice on Leaking keg posts  (Read 1342 times)

Offline wingnut

  • Brewer
  • ****
  • Posts: 309
  • Plainwell MI
    • View Profile
Advice on Leaking keg posts
« on: August 29, 2010, 08:21:47 AM »
Hi all,

I just got the final pieces of keg system setup, cleaned and rebuilt the kegs, replaced seals...etc ... Spent a day locating and fixing leaks... and carbed up my first batch of beer.   

However, when I plugged in my faucet line, I had beer leaking past the post seal between it and the connector.  No amount of wiggling the connector, adding keg lube... etc would keep the beer from spewing past the seal. 

I finally removed the "brand new" o-ring and put one of the used ones on... and the leak went away. 

I got the new o-rings from a popular Homebrew supplier, and the gas side worked great... so I am wondering if my experience is unique... if there is a better cure than using an old seal, or if there is something to look for that will identify the o-ring as "not up to par" (aside from nicks and cuts).

Any and all wisdom is welcome!

Thanks,
-- Wingnut - Cheers!

Offline majorvices

  • Global Moderator
  • I must live here
  • *****
  • Posts: 7776
  • Polka. If its too loud you're too young.
    • View Profile
    • Yellowhammer Brewing Company
Re: Advice on Leaking keg posts
« Reply #1 on: August 29, 2010, 02:01:55 PM »
Its never happened to me before but it could be that that one o-ring you had was simply manufactured wrong. Or you cracked it while installing it.

FTR I bought about 100 o-rings from McMaster carr a few years ago and never had a problem and they were a couple cents a piece. I'll try and see if I can find the part #. I have enough to last me a good bit longer still.
Keith Y.

Vote Jonathan Fuller for Governing Committee!

Offline tschmidlin

  • I must live here
  • **********
  • Posts: 8195
  • Redmond, WA
    • View Profile
Re: Advice on Leaking keg posts
« Reply #2 on: August 29, 2010, 03:27:27 PM »
Here are the McMaster-Carr part numbers and the prices last time I ordered:

Post o-ring ($2.15 for 100):
http://www.mcmaster.com/#9452k23/

Dip tube o-ring ($1.96 for 100):
http://www.mcmaster.com/#9452k172/

Lid o-ring ($12.69 for 10):
http://www.mcmaster.com/#9452k218/
Tom Schmidlin

Offline wingnut

  • Brewer
  • ****
  • Posts: 309
  • Plainwell MI
    • View Profile
Re: Advice on Leaking keg posts
« Reply #3 on: August 30, 2010, 06:54:30 PM »
Cool!  Thanks for the info!   ;D So maybe it was just my bad luck...  Regardless, at least now I can have a relatively unlimited supply to try.



-- Wingnut - Cheers!

beveragebob

  • Guest
Re: Advice on Leaking keg posts
« Reply #4 on: September 27, 2010, 04:41:40 PM »
Maybe a a bad poppet?

Offline 6thstreet

  • Cellarman
  • **
  • Posts: 45
    • View Profile
Re: Advice on Leaking keg posts
« Reply #5 on: September 28, 2010, 10:37:50 AM »
Maybe a a bad poppet?

Thats been my problem lately.  I pull off the ball lock and get quite the spray of beer in the face.  :'(  The poppet seems to get pushed down and to the side just a bit allowing pressure or beer to escape.  Now out of habit I vent the keg before removing the ball lock.

Offline gordonstrong

  • Senior Brewmaster
  • ******
  • Posts: 1355
    • View Profile
    • BJCP
Re: Advice on Leaking keg posts
« Reply #6 on: September 28, 2010, 12:51:42 PM »
Poppets are cheap.  Keep several around as spares.  Also some pressure relief valves and various O-rings.  It's so easy to lose a batch of beer if your kegs aren't tuned properly.  Don't screw around with them.  Just pull apart the offending piece and replace it.  Don't think of them as permanent pieces; think of them like batteries in a remote control.  They wear out and then you pitch them.
Gordon Strong • Beavercreek, Ohio • AHA Member since 1997 • Twitter: GordonStrong

Offline 6thstreet

  • Cellarman
  • **
  • Posts: 45
    • View Profile
Re: Advice on Leaking keg posts
« Reply #7 on: September 28, 2010, 01:33:01 PM »
yeah I do but dont know until they spray me in the face

Offline wingnut

  • Brewer
  • ****
  • Posts: 309
  • Plainwell MI
    • View Profile
Re: Advice on Leaking keg posts
« Reply #8 on: September 29, 2010, 08:47:00 PM »
Naw, it was not a bad poppet, replaceing just the O-ring on the post took care of it.  Being new to kegs (this was my first one) I was looking for hints of operator error, and experaince on reliability of o-rings.  (Starting out with a .500 O-ring percentage is kind of alarming, and I was looking to find out that is common or if I was just lucky)

As all have suggested, I am well armed with a collection of o-rings, posts, poppets, and disconnects.  As Gordon pointed out, it is easy to ruin a batch of beer, and I would hate the cause of a bad batch to be a 2 dollar or 20 cent part!

Thanks all!
-- Wingnut - Cheers!

Offline euge

  • I must live here
  • **********
  • Posts: 7551
  • Estilo Casero
    • View Profile
Re: Advice on Leaking keg posts
« Reply #9 on: September 30, 2010, 12:55:03 AM »
Take a look at the poppits and posts with a loop or maginifier. The metal on metal wears them out and they get grooved and scalloped. Lube helps. I use olive oil. Lightly.

The first principle is that you must not fool yourself, and you are the easiest person to fool. -Richard P. Feynman