Author Topic: mini-mash conversion test?  (Read 3363 times)

Offline euge

  • I must live here
  • **********
  • Posts: 7396
  • Estilo Casero
    • View Profile
Re: mini-mash conversion test?
« Reply #15 on: October 26, 2011, 01:20:12 AM »
Mashing a full batch isn't difficult. Do it.

You should buy those kettle upgrades anyway if you decide to keep your current system. A brewmometer and weldless ball-valve are indispensable.



The first principle is that you must not fool yourself, and you are the easiest person to fool. -Richard P. Feynman

Online Jimmy K

  • Official Poobah of No Life.
  • *
  • Posts: 3502
  • Delaware
    • View Profile
Re: mini-mash conversion test?
« Reply #16 on: October 26, 2011, 01:05:14 PM »
Buy the bigger kettle with ball valve and a chiller first. You can still do mini-mashes while stepping up to full boils. 
Delmarva United Homebrewers - President by inverse coup - former president ousted himself.
AHA Member since 2006
BJCP Certified: B0958

Offline a10t2

  • Official Poobah of No Life.
  • *
  • Posts: 3488
  • Ask me why I don't like Chico!
    • View Profile
    • SeanTerrill.com
Re: mini-mash conversion test?
« Reply #17 on: October 27, 2011, 08:20:11 AM »
Good water with pH in the 5.0-5.4 range. But I did not check the pH during or after the mash. Next time I will do that for certain. I have the cheap pH strips, but that is good enough for now.

There's a red flag. Where is the water coming from? Municipal supplies will ALWAYS have pH > 7 because it's easier on the pipes. If you're using the cheap strips, that's probably the issue. They're wildly inaccurate. You can get 100 ColorpHast strips for ~$20, and they're well worth it.

The first things to check are still instrument calibration and crush though.
Beer is like porn. You can buy it, but it's more fun to make your own.
seanterrill.com/category/brewing
twomilebrewing.com

Offline rbclay

  • Assistant Brewer
  • ***
  • Posts: 214
  • Northfield, MN
    • View Profile
Re: mini-mash conversion test?
« Reply #18 on: October 27, 2011, 04:24:31 PM »
Good water with pH in the 5.0-5.4 range. But I did not check the pH during or after the mash. Next time I will do that for certain. I have the cheap pH strips, but that is good enough for now.

There's a red flag. Where is the water coming from? Municipal supplies will ALWAYS have pH > 7 because it's easier on the pipes. If you're using the cheap strips, that's probably the issue. They're wildly inaccurate. You can get 100 ColorpHast strips for ~$20, and they're well worth it.

The first things to check are still instrument calibration and crush though.

my water is good. Chippewa Falls spring water or St. Paul filtered tap water. Both have proven to be great for brewing. I had Chippewa Falls send me their water report. I said it was in the range of 5-5.4 only because of the cheap strips. Definitely not using my municipal tap water. I have friends in St. Paul that let me fill up when I'm in the area, or the spring water I can get at the grocery store.
my thermocoupler is good. calibrated with lab instruments at a club meeting last year. crush certainly may be a variable, but I err on the side of too fine, I think, so I'll have to wait to repeat a particular recipe with the crush as the only variable to check that.
Randy Clay
Milltown Mashers
https://www.facebook.com/groups/404574082932834/
BJCP Certified