Membership questions? Log in issues? Email info@brewersassociation.org

Author Topic: Man jewlery  (Read 8300 times)

Offline redbeerman

  • Senior Brewmaster
  • ******
  • Posts: 1849
  • On the banks of the mighty Susquehanna in MD
Re: Man jewlery
« Reply #45 on: February 09, 2011, 11:05:48 am »
I rarely wear jewelry, not even my wedding band, especially now that I can't get the damn thing off if I put it on.  Anyway, working with electricity, as I do, and wearing jewelry, is oft times a bad idea. ;)
CH3CH2OH - Without it, life itself would be impossible.

[441, 112.1deg] AR

Jim

Offline weazletoe

  • Brewmaster General
  • *******
  • Posts: 2437
  • Howland, Ohio
Re: Man jewlery
« Reply #46 on: February 09, 2011, 12:48:41 pm »
And some +1 to the dings on the ring from work in general.

Three of my four rings are actually tungsten carbde. Try an scratch that!  ;D
A man works hard all week, so he doesn't have to wear pants all weekend.

Offline hamiltont

  • Brewmaster
  • *****
  • Posts: 988
  • Location: Eastern Nebraska
Re: Man jewlery
« Reply #47 on: February 09, 2011, 12:52:44 pm »
Kryptonite.....  ;D
If Homebrew & BBQ aren't the answer, then you're askin' the wrong questions... Cheers!!!

Offline weazletoe

  • Brewmaster General
  • *******
  • Posts: 2437
  • Howland, Ohio
Re: Man jewlery
« Reply #48 on: February 09, 2011, 01:09:01 pm »
You just had to one up me, didn't you? You could not just let have this one?!?!   ;D
A man works hard all week, so he doesn't have to wear pants all weekend.

Offline hamiltont

  • Brewmaster
  • *****
  • Posts: 988
  • Location: Eastern Nebraska
Re: Man jewlery
« Reply #49 on: February 09, 2011, 01:35:26 pm »
You just had to one up me, didn't you? You could not just let have this one?!?!   ;D
Saw an open door & walked right in...  ;)  Cheers!!!
If Homebrew & BBQ aren't the answer, then you're askin' the wrong questions... Cheers!!!

Offline tubercle

  • Senior Brewmaster
  • ******
  • Posts: 1639
  • Sweet Caroline
Re: Man jewlery
« Reply #50 on: February 09, 2011, 04:21:46 pm »
Have any of you welding/fabrication types ever tried making a ring.

Seems like slicing off a proper sized piece of pipe and polishing it up real nice would work.
Sweet Caroline where the Sun rises over the deep blue sea and sets somewhere beyond Tennessee

Offline gmac

  • Brewmaster General
  • *******
  • Posts: 2165
  • London, Ontario
Re: Man jewlery
« Reply #51 on: February 10, 2011, 10:41:22 pm »
Have any of you welding/fabrication types ever tried making a ring.

Seems like slicing off a proper sized piece of pipe and polishing it up real nice would work.

Have you ever taken a beer bottle and just lightly clinked the mouth of it repeatedly against the mouth of another bottle?  If you do it just right, it'll snap off cleanly right below the base where the cap goes on.  I did this once and then using some wet sandpaper, smoothed the rough edges and made a ring out of it.  A girl I knew wore it for quite a while until she dropped it when she was playing around with it and it became little ring shards...

Of course, everyone on here would never do that because they'd rather fill the bottle...

Offline SwashBuckling Drunk

  • Assistant Brewer
  • ***
  • Posts: 241
  • Boring, Oregon
Re: Man jewlery
« Reply #52 on: February 11, 2011, 08:32:37 am »
Only a wedding band for me.  I only take it off to split firewood w/ an ax.  For some reason my finger gets pinched.